Epoxy floor paint is a special coating consisting of epoxy resin, color paste, filler (quartz powder, talc powder, titanium dioxide powder, etc.), additives (leveling agent, defoamer) and corresponding curing agent. It is mainly used on concrete and cement floor. Epoxy floor is suitable for wear-resistant and impact-resistant places such as electronics, electrical appliances, machinery, communications, food, medicine, moulds, clothing, plastics, tobacco and chemical industry, especially forklift trucks, heavy-duty forklift trucks and automobiles. It has excellent impact resistance, high load, wear resistance, seamless, easy to clean, moisture-proof, dust-proof, general chemical corrosion resistance, and can be used for anti-slip or matte effect. For the epoxy floor paint project after completion of acceptance, many consumers may not understand, below, epoxy floor paint manufacturers to you in detail.一、配资盘漆常溫固化二天後验收項目：
1. Acceptance and acceptance of floor paint after curing at room temperature for two days: 1、漆漆膜顔色一致、均一，無浮色、發花現象，無明顯色差，明暗深淺一致,無漏光現象;
1. Floor paint film is uniform and uniform in color. There is no floating or blooming phenomenon, no obvious color difference, light and shade are identical, and no light leakage phenomenon.
2. The surface of the floor paint film is smooth and smooth, and there is no scratch phenomenon when touching the paint film by hand. The glossiness should meet the design requirements (high gloss (> 90), gloss (> 70), half gloss (> 50-70), and the flat coating type is glossy and water-borne is half glossy (~no gloss).
3. There are no coarse impurities, but the floating dust in the air is allowed to fall on the minimal defects.
3. Floor paint film shall not have the following obvious defects: brush marks, shrinkage holes, bubbles, small particles, drum hair, cracks, bottom leakage, abrasion points, wrinkles, knife marks;
4. When dealing with complex terrain such as Yinyang angle and chamfer angle, there should be no omission and irregularity, especially the accumulation of doors, and the opening and closing of doors will not scratch the floor paint film.
5. Make the construction site clean, tidy, sprinkle paint, paint matching operation site, coating beyond the scope of construction, clean and clean, construction tape, newspapers, strips and other waste disposal clean.
2. The acceptance items of floor paint should be checked and accepted seven days after curing at room temperature.
After curing at room temperature for seven days, the floor paint film achieves the required performance. At present, there is no domestic standard in this respect. Usually, the following methods are adopted:1、硬度：用HB鉛筆劃漆膜，無劃痕为合格。
1. Hardness: Scratch paint film with HB pencil, no scratch is qualified.2、沖擊強度及韌性：用一公斤鋼球從一米高處落下，看其對漆膜的影響，允許有漆膜下陷，但不允許有裂紋;
2. Impact strength and toughness: a kilogram of steel ball falling from a height of one meter to see its impact on the paint film, allowing for film subsidence, but not cracks;3、附着力。根據現場情況檢測地坪漆附着力，主要有以下幾種方法：a.拉開法，使用測試儀，要求附着力大于1.5Mpa;b.膠帶法。这一種方法用于金屬表面，并且要求附着力等級大于3級;c.同樣也是适用與金屬表面的劃格膠帶法。要求附着力等級小于2級。
3. Adhesion. According to the field situation, there are mainly the following methods to test the adhesion of floor paint: A. pull-out method, using the tester, requires the adhesion greater than 1.5 Mpa; B. tape method. This method is applied to metal surface, and requires that the adhesion level is greater than 3 grades; C. It is also applicable to the scratch tape method with metal surface. Attachment level is required to be less than 2.4、厚度。如果地面基地是金屬，要檢查其幹膜厚度，必須是在地坪漆施工三個月内檢查，并且要求85%以上的測試點厚度要求达到或高于标準。
4. Thickness. If the ground base is metal, to check the dry film thickness, it must be checked within three months of the floor paint construction, and require more than 85% of the test point thickness requirements to meet or exceed the standard.
标簽:   地坪 配资盘 配资盘施工 配资盘漆 無錫配资盘